基于B-P神经网络的环境质量评价方法

提出可将环境质量评价的无论是定量指标还是定性参数转化成"二进制"的"1"或"0",进而将这种二进制数引入B-P网络.通过实例探讨,这种新的B-P网络既适用于定量指标的水质参数又适用于定性指标的水质参数.     

基于BDD考虑共因失效的接触网系统可靠性分析

为分析共因失效对高速铁路接触网系统的影响，将二元决策图(Binary Decision Diagram，BDD)与共因失效理论引入到接触网系统可靠性分析中。利用逻辑相邻优先组合法(Logic Neighbor Priority Connect，LNPC)将高速铁路接触网系统的故障树模型转化为BDD模型并求取其可靠度表达式，利用隐式方法对考虑了共因失效的接触网系统可靠度进行计算，利用MATLAB绘制考虑共因失效和不考虑共因失效情况下接触网系统可靠度变化曲线。研究结果表明:提出的分析方法适用于接触网系统的可靠性分析，为接触网系统的可靠性分析提供了一定的理论依据。     

混合液体火灾爆炸危险性——闪点预测与实验研究

支持向量机应用核函数技术,已经成为当前国际上一个研究的热点,由于支持向量机具有良好的理论基础和泛化性能,可将其引入到混合液体闪点预测的研究之中,以期建立准确、高效的预测模型。本文建立了一个基于支持向量机的理论模型,用于预测二元互溶混合液体的闪点。根据所研究混合液体的物理性质,选择了纯物质的粘度、表面张力、配比、燃烧下限等物理参数来表征闪点,以这些参数作为输入参数,二元混合液体的闪点作为输出值,应用支持向量机方法对两者之间的内在定量关系进行模拟。结果表明,闪点预测值与实验值符合良好。本方法的提出为工程上提出了一种预测二元互溶液体闪点的有效方法,可应用于评估混合溶液的火灾爆炸危害性及本质较安全设计。     

铁锰复合氧化物/壳聚糖珠:一种环境友好型除磷吸附剂

采用两步法制备了一种环境友好型除磷基吸附剂——铁锰复合氧化物/壳聚糖珠(FMCB),对其进行了表征,并对其磷吸附行为进行了系统研究.表征结果表明,该吸附剂为多孔纤维结构,比表面积为248 m~2·g~(-1),孔容为0.37 m~3·g~(-1).吸附实验结果表明,FMCB对磷的吸附容量远高于纯的壳聚糖颗粒,且Langmuir模型能更好地拟合FMCB对磷的吸附,最大吸附量为13.3 mg·g~(-1)(pH 7.0);准二级动力学模型能更好地拟合FMCB对磷吸附的动力学实验数据;溶液pH对磷的吸附影响较大,随着pH的增大,磷的吸附量逐渐降低;共存的Ca~(2+)和Mg~(2+)对磷吸附略有促进,而共存阴离子对磷吸附具有抑制作用,影响大小顺序为:SiO_3~(2-)CO_3~(2-)SO_4~(2-)≥Cl~-.吸附磷后的FMCB可用NaOH溶液进行脱附再生,并可重复使用.在进水磷初始浓度为3 mg·L~(-1)条件下,吸附达到穿透时(出水磷浓度达0.5 mg·L~(-1)),可处理约800个柱体积的模拟含磷废水.     

二元联合作用藻红外测试方法——以重金属为例

为检验二元联合作用藻红外测试方法的可行性,用Cu~(2+)、Fe3+、Mn~(2+)、Al3+、Cr3+、Hg~(2+)、Cd~(2+)、Pb~(2+)、Zn~(2+)进行了二元联合作用测试实验。结果显示:联合药液的参照浓度与单药液的参照浓度比为0.5:0.25的有15组二元组合,为2.0:1.0的有10组二元组合,为1.0:0.5的有11组二元组合;在9种重金属的36组二元联合作用测试结果中出现拮抗作用、相加作用、协同作用,表明联合作用类型表现出多样性;14组拮抗作用中单组的再现性为50%~100%、多组的再现性的出现率为93%、单组的重现性为67%~100%、多组的重现性的出现率为100%,21组相加作用中单组的再现性为50%~100%、多组的再现性的出现率为86%、单组的重现性为67%~100%、多组的重现性的出现率为100%,1组协同作用重现性67%;36组联合作用测试结果的再现性为50%~100%、再现性的出现率为86%,重现性为67%~100%、重现性的出现率为100%。上述分析可知,9种重金属的36种二元联合作用测试结果具有较好的多样性、再现性、重现性,表明测试条件、藻温测试方法、三指标评价法能够保证藻响应温差和藻响应药品评价结果的质量,参照浓度分析方法、联合作用评价方法能够控制联合作用分析结果的质量;藻响应的有毒有害物都存在敏感浓度,用参照浓度分析方法可分析出藻响应有毒有害物的参照浓度。因此,藻红外测试技术可以用于测试重金属、农药、有机药品、抗生素等的二元联合作用。     

Experimental thermal storage research of organic binary phase change materials in building environment

This paper aims to reveal the heat transfer mechanism of low-temperature phase change material (PCM) and design PCM heat storage device in building heating environment. Firstly, low-temperature binary PCMs of lauric acid and stearic acid are prepared, and their thermal properties are investigated by DSC. Then, shell and tube latent heat thermal energy storage units are conducted, and heat transfer experiments are carried out to analyze the heat transfer mechanism of PCM. The results demonstrate that natural convection plays an important role in heat transfer process, and the heat storage efficiency of PCMs can be significantly enhanced by increasing the fin width and improving the inlet heat transfer fluid (HTF) temperature. Furthermore, some proposals are put forward to guide the design of PCM storage device in building heating environment.     

基于回归分析的火灾发生气象因子的研究

利用二元回归分析法,对火灾发生次数、空气湿度、风速进行回归分析并检验,得出了火灾发生次数、空气湿度、风速三者之间的显著线性关系。     

A preliminary investigation into the physical and chemical properties of biomass ashes used as aggregate fillers for bituminous mixtures

Fly and bottom ashes are the main by-products arising from the combustion of solid biomass. Since the production of energy from this source is increasing, the processing and disposal of the resulting ashes has become an environmental and economic issue. Such ashes are of interest as a construction material because they are composed of very fine particles similar to fillers normally employed in bituminous and cementitious mixtures. This research investigates the potential use of ash from biomass as filler in bituminous mixtures. The morphological, physical and chemical characteristics of 21 different ashes and two traditional fillers (calcium carbonate and “recovered” plant filler) were evaluated and discussed. Leaching tests, performed in order to quantify the release of pollutants, revealed that five ashes do not comply with the Italian environmental re-use limits. Experimental results show a wide range of values for almost all the investigated properties and a low correlation with biomass type in terms of origin and chemical composition. Furthermore, sieving and milling processes were found to improve the properties of the raw material in terms of grading and sample porosity. The effectiveness of these treatments and the low content of organic matter and harmful fines suggest that most of the biomass ashes investigated may be regarded as potential replacements for natural filler in bituminous mixtures.     

事故二叉树计算机算法

根据《数据结构》中的二叉树算法,结合事故树算法的特点,提出事故二叉树算法。该算法是对事故树求解算法的有益补充和发展,具有广阔的应用前景和现实意义     

Moderation of dust explosions

Inherent safety is a proactive approach to process safety in which hazards are removed or minimized so as to reduce risk without engineered (add-on) or procedural intervention. Four basic principles are available to attain an inherently safer design—minimization, substitution, moderation, and simplification. The subject of the current paper is the principle of moderation as it applies to the prevention and mitigation of dust explosions.

Moderation can be achieved by processing a material under less severe operating conditions or by processing the material in a less hazardous form. With respect to the latter approach, it may be possible to alter the composition of a dust by admixture of solid inertants, or to increase the dust particle size so as to decrease its reactivity. Additionally, avoidance of the formation of hybrid mixtures of explosible dusts and flammable gases is an application of moderation of the material hazard.

Several examples are given for each of the above three forms of moderation. The discussion on admixture of solid inertants includes examples from the following industrial applications: (i) refractory materials manufacturing, (ii) food processing, (iii) power generation, (iv) industrial recycling, and (v) foundry shell mold fabrication. The importance of particle size consideration is explained first from the perspective of engineering tools such as the Dow Fire & Explosion Index, and professional guidance on the definition of a dust and suitable particle sizes for explosibility testing. Industrial examples are then drawn from the following areas: (i) rubber recycling and textile manufacturing, (ii) industrial recycling, (iii) wood processing, (iv) dry additive handling (polyethylene facility), (v) polyethylene production, (vi) carbon block recycling, and (vii) coal mining. The concluding discussion on hybrid mixtures includes brief cases from the process safety literature.